icon-menu-x-close

High Vacuum vs. Medium Vacuum Bakeout/Drying Ovens | Part 1

Vacuum drying and high vacuum bakeout are often discussed as if they are the same process, but they serve very different purposes. In this two-part series, we’ll explain the differences between vacuum drying, high vacuum bakeout, and ultra-high vacuum bakeout, then examine how engineers can determine which approach is appropriate for their application.

  • Part 1: Understanding the differences between vacuum drying, high vacuum bakeout, and UHV bakeout.
  • Part 2: How to evaluate application requirements and select the right process.
What Is the Difference Between Vacuum Drying and High Vacuum Bakeout?

The primary difference between vacuum drying and high vacuum bakeout is the process objective. Vacuum drying removes moisture and solvents. High vacuum bakeout reduces outgassing by removing adsorbed water and trace contaminants that can affect performance later.

Ask five engineers what a “bakeout oven” is, and you’ll likely get five different answers.

In some facilities, bakeout means heating parts under vacuum to dry them after cleaning. In aerospace, research, and contamination-sensitive applications, bakeout often means something much more specific: a high-vacuum process used to reduce outgassing before hardware enters service.

Both processes use heat. Both processes use vacuum. But they solve different problems.

The real distinction isn’t the word bakeout. It’s the combination of vacuum level and process objective.

What Is a Vacuum Bakeout?

A vacuum bakeout is a process that uses heat and vacuum to remove moisture, adsorbed gases, and volatile contaminants from materials or assemblies.

The challenge is that the term bakeout is frequently used to describe several different processes. One engineer may be describing vacuum drying, while another is describing preparation for a contamination-sensitive aerospace application.

In practice, most bakeout-related processes fall into three categories:

  • Vacuum drying (often called medium vacuum bakeout)
  • High vacuum bakeout
  • Ultra-high vacuum (UHV) bakeout

While the equipment may look similar from the outside, the purpose and required performance can be very different.

What Is Medium Vacuum Bakeout (Vacuum Drying)?

Medium vacuum bakeout is, in most practical applications, simply vacuum drying.

These processes typically operate from rough vacuum levels down to approximately 10⁻³ Torr, with temperatures often limited to around 100° C due to material, elastomer, or O-ring constraints. This range was specifically discussed during the development of this article as representative of many industrial drying applications.

At these vacuum levels, the primary benefit of vacuum is that it lowers the boiling point of moisture and solvents. Water evaporates more readily, allowing parts to dry more quickly and at lower temperatures than they would at atmospheric pressure.

  • Common applications include:
  • Drying parts after aqueous cleaning
  • Removing residual moisture before assembly
  • Drying products that may be sensitive to higher temperatures

The key takeaway is that vacuum drying is intended to remove bulk moisture and solvents. It is focused on making parts dry rather than minimizing long-term outgassing.

What Is High Vacuum Bakeout?

High vacuum bakeout is used when the goal shifts from drying to outgassing reduction.

In high vacuum environments, contaminants released from heated surfaces are less likely to reattach elsewhere in the chamber and more likely to be removed by the pumping system entirely.

This matters because many contamination-sensitive applications are not limited by bulk moisture. Instead, they are limited by trace amounts of adsorbed water vapor, cleaning residues, hydrocarbons, and other volatile compounds.

According to LACO’s Vacuum Bake-Out of Parts application note, vacuum bakeout systems intended for high-purity applications commonly use pumping systems capable of reaching pressures below 10⁻⁶ Torr and heating systems capable of temperatures exceeding 200° C. The application note also notes that approximately 100° C may be sufficient to remove loosely bound water layers, while more demanding applications may require significantly higher temperatures.

For many real-world applications, however, bakeout temperatures are often constrained by the hardware itself rather than the oven’s capability.

High vacuum bakeout is commonly used for:

  • Aerospace and satellite hardware
  • Optical assemblies
  • High-reliability electronics
  • Scientific and research equipment
  • Components intended for high-vacuum environments

The objective is not simply dry parts. The objective is low-outgassing parts.

Vacuum Drying vs. High Vacuum Bakeout at a Glance

Process 

Typical Vacuum Range 

Typical Temperature 

Primary Goal 

Vacuum Drying 

~20 Torr to 10⁻³ Torr 

Often up to ~100° C 

Remove moisture and solvents 

High Vacuum Bakeout 

Commonly below 10⁻⁵ Torr 

Hardware dependent 

Reduce outgassing and contamination 

UHV Bakeout 

Below 10⁻⁸ Torr 

Often 200° C+ 

Support ultra-high vacuum operation 

Why High Vacuum Matters

The importance of vacuum level becomes clear in contamination-sensitive applications.

NASA’s thermal vacuum bakeout specification for flight hardware states:

“The bakeout procedure consists of heating the flight hardware in a clean, certified vacuum system (<1 × 10⁻⁵ Torr pressure) at the highest temperature permitted without endangering the hardware.”

The important takeaway is not the exact pressure threshold.

The takeaway is that for contamination-sensitive hardware, vacuum level itself becomes part of the process requirement. The objective is no longer simply removing moisture. The objective is reducing molecular contamination and outgassing risk.

Where Ultra-High Vacuum Fits In

Ultra-high vacuum bakeout takes the same concept a step further.

To achieve pressures below 10⁻⁸ Torr, systems are commonly baked at elevated temperatures to accelerate the removal of adsorbed water and other contaminants that would otherwise take an extremely long time to desorb at room temperature. UHV references commonly describe bakeout temperatures in the range of approximately 100° C to 300° C, while many UHV systems are also baked in the 150° C to 250° C range depending on the design and limitations of the hardware.

At these vacuum levels, chamber materials, seals, heaters, instrumentation, and feedthroughs all become critical design considerations.

UHV bakeout is not simply a more aggressive version of vacuum drying. It is a specialized process used to help achieve and maintain ultra-high vacuum conditions.

Key Takeaway: Vacuum Drying vs. High Vacuum Bakeout

If you’re trying to remove moisture, vacuum drying is often sufficient.

If you’re trying to reduce outgassing, improve contamination control, or prepare hardware for operation in a vacuum environment, high vacuum bakeout is typically required.

In simple terms:

  • Vacuum drying removes bulk moisture.
  • High vacuum bakeout removes adsorbed water and reduces outgassing.
  • UHV bakeout helps achieve and maintain ultra-high vacuum conditions.

The vacuum level—not temperature alone—is what defines the process.

In Part 2, we’ll look at how to determine which approach is appropriate for your application and identify the questions engineers should ask before specifying equipment.

Book a Meeting

Want to discuss your thermal vacuum testing requirements with our team? Use the Space Tech Expo Europe B2B platform to reserve a meeting.

Related Resources